Search This Blog

Tuesday, March 18, 2014

an easy to build FUZZ

this one here's an adaptation of P. Hemmo's modern Bazz Fuss fuzz. low parts count, massive tones. you can swap out the output cap with a 1uF cap for more low end.

NOTE: to use the PCB, right click on the PCB image and paste onto a blank document. print to a white paper. copy to a photopaper using a laser copier.







Monday, February 17, 2014

An ENVELOPE FILTER project

Ah, the good old envelope filters, expressive little boxes of wah-wah goodness without the treadles. Basically, the envelope filter sweeps a certain range of boosted frequencies that is triggered by detected envelope of a string's initial attack. Pretty nifty.

The following is the Nurse Quacky project (which is a bit tweaked EHX/Dr. Q circuit). Original circuit by the good guys of Home-wrecker.

THE SCHEMATIC (click for larger image)







THE PCB [note: to use the pcb, right click on the pcb image and paste onto a blank Word sheet. Print a copy, and photocopy that print into a photopaper.]



THE PARTS AND LAYOUT (click for larger)






the parts list:



Part        Value         
C1          10nF          
C2          10nF          
C3          4.7nF         
C4          4.7nF
C5          100nF      
C6          22uF          
C7          47uF          
C8          100uF         
C9          1nF           
D1          LED5MM        
D2          LED5MM        
D3          IN4002         
IC1         LM358         
Q1          2N3904        
R1          47K           
R2          47K           
R3          470K         
R4          470K          
R5          47K           
R6          10K           
R7          3M3           
R8          51             
R9          220           
R10         470K          
R11         22K           
R12         27K           
R13         27K           
R14         100           
RANGE       B25K          
SENSITIVITY B100K         
ATTACK         B1K            



(this project is for personal use only. not for sale or commercial use. all rights reserved by the owner.)



Thursday, January 23, 2014

PSYCHE1: A simple VIBE pedal project

The following is a simple Vibe pedal project consisting of a unity gain stage and an oscillator driving an LED (light emitting diode) and LDR (light-dependent resistor) to generate a single stage 180degree phase shift.

I omitted a depth control since it has fairly minimal use, but you may opt to install one just the same: simply use a 25K potentiometer in place of the 30K bias trimmer.

Its effect is very subtle, and many like the circuit for this characteristic, as opposed to the usual balls-to-the-wall effects that some use.



(note: to use the pcb, right click on the image and paste onto an empty Word document, and print out.)


 


This project is for personal use only, not for sale or any other commercial use. Alterations to the original image is infringement.

Thursday, December 12, 2013

BUFFER

Any guitarist or bassist will definitely benefit from having a buffer. I'm too stumped to write technical stuff about buffers, so here are links instead:



What’s the Big Deal About True Bypass?
By DAVE HUNTER
Thu, 13 Dec 2012


rss ShareThis


The phrase “true bypass” has become a watchword for the pedal industry, and it’s high on most buyers’ lists of priorities. But is true bypass as essential a feature as so many pedal makers would have us believe?
True bypass, aka “hardwired bypass,” occurs when the input of an effect is wired directly to the output via the on/off switch when it’s in the “off” position, rather than being routed through (or connected to) part of the circuitry the entire time.
read more here,
http://www.guitarplayer.com/article/what%E2%80%99s-the-big-deal-about-true-bypass/150189


Let's build one.






(note: right click on the PCB image and paste onto empty Word document for printing.)





THAT'S IT!

This project is for personal use only, not for sale or any other commercial use. Alterations to the original image is infringement.

Sunday, September 1, 2013

Starting Out

in 2 weeks' time, i'll be posting effects projects for guitars on this blog. so stay tuned!